Production of a Wheel Support (Cutting). Approximately 40.0 mm OD x 10.0 mm long. Please see drawing for all specifications.

This black nylon part hold the axel for a skate type wheel. 4 needed for the finished chair. No specific finish required. One threaded hole for connecting the chair. See drawing for details.

Production of a Outer Arm Flange (Cutting). Approximately 1735.0 mm x 402.5 mm x 3.0 mm. Please see drawing for all specifications.

Cut from 3mm thick 5054 H34 aluminum sheet (can be water jet cut). Polished finish. Welded to the outer edge of the arm rests and the edge slightly rounded. Designed to add rigidity to the arm rests. See drawing for details and dxf for cutting.

Production of a Main Seat (Bending). Approximately 2139.0 mm x 500.0 mm x 3.0 mm. Please see drawing for all specifications.

Cut and formed from 3mm thick 5054 H34 aluminum sheet, 500mm wide. Polished finish and a series of holes for rivets and bolts.

Production of a Aluminum angle support (Bending). Approximately 405.0 mm x 22.0 mm x 22.0 mm. Please see drawing for all specifications.

Made from Aluminum angle this part connect the arm rests to the main seat at the leg end. A series of holes for rivets are drilled. Can be made from 3/4"x 3/4" aluminum angle. De burred, mill finish.

Production of a Inner Arm Flange (Cutting). Approximately 1735.2 mm x 402.5 mm x 3.0 mm. Please see drawing for all specifications.

This part is cut from 3mm thick 5054 H34 aluminum sheet. Can be waterjet cut from the attached dxf file. Polished finish. A series of holes for rivets.

Production of a Connecting Bung (Cutting). Approximately 40.0 mm OD x 30.0 mm long. Please see drawing for all specifications.

Made from black nylon round bar this bung is used to connect the arm rests and main chair together. 2 threaded holes. No specific finishing requirements as the parts will be hidden.

Production of a Cassette Side Walls (Cutting). Approximately 652.0 mm x 538.0 mm x 3.0 mm. Please see drawing for all specifications.

Cut from 3mm thick 5054 H34 Aluminum sheet. 2 per cassette need cutting. Can be waterjet cut from the supplied dxf file. Please see drawing for details. Polished finish. These are welded to the sides of the cassette enclosing it. Must be a water tight join.

Production of a Cassette Shelves (Bending). Approximately 494.0 mm x 435.0 mm x 307.0 mm. Please see drawing for all specifications.

This is the internal structure for the Cassette. Cut and formed from 3mm thick aluminum sheet. Polished finish. Please see drawing for details.

Production of a Cassette Lip (Cutting). Approximately 404.0 mm x 9.0 mm x 3.0 mm. Please see drawing for all specifications.

This part is a simple lip that finishes off the top edge of the casstte lip. Cut from aluminum 5054 H34 and joined to the 3 sections of the cassette lid. Polished finish. Please see drawing for details.

Production of a Cassette Lid Outer (Bending). Approximately 596.0 mm x 404.0 mm x 3.0 mm. Please see drawing for all specifications.

This is the outer most laminate of the cassette lid. Formed from 3mm thick 5054 H34 aluminum and polished. Please see drawing for details.

Production of a Cassette Lid Middle (Bending). Approximately 532.0 mm x 344.0 mm x 3.0 mm. Please see drawing for all specifications.

The middle laminate of the cassette lid. A series of holes drilled in the sides of this sheet to allow for some magnets to be inserted. Formed from 3mm thick 5054 H34 aluminum sheet. Can be unfinished as it will be sandwiched between two parts and not seen. See drawing for details.

Production of a Cassette Lid Inner (Bending). Approximately 590.0 mm x 404.0 mm x 3.0 mm. Please see drawing for all specifications.

The inner laminate of the lid for the cassette. Formed from 3mm thick 5054 H34 Aluminum sheet. Polished. See drawing for details.

Production of a Cassette Cover (Bending). Approximately 682.5 mm x 494.0 mm x 3.0 mm. Please see drawing for all specifications.

Formed from 3mm 5054 H34 aluminum sheet. Polished finish. Please see attached pdf for details.

Production of a Cassette Back (Bending). Approximately 1116.0 mm x 494.0 mm x 3.0 mm. Please see drawing for all specifications.

Formed 3mm 5054 H34 aluminum sheet. Polished finish. Please see attached pdf for specifications.

Production of a Battery Panel Cover (Cutting). Approximately 280.0 mm x 230.0 mm x 3.0 mm. Please see drawing for all specifications.

Cut from 3mm thick 5054 H34 aluminum sheet. Can be waterjet cut for accuracy. Please see attached pdf for details and dxf for cutting.

Production of a Arm Rests (Bending). Approximately 1735.0 mm x 402.5 mm x 3.0 mm. Please see drawing for all specifications.

Formed aluminum arm rest for lounge chair 3mm thick 5054 H34 aluminum sheet. I need two of these per lounge chair. Polished finish.

Production of a Cassette Inner Flange_update (Bending). Approximately 670.0 mm x 494.0 mm x 3.0 mm. Please see drawing for all specifications.

Cut and formed from 3mm thick 5054 H34 aluminum sheet. This part acts as a slide for the cassette lid. A series of 1.5mm holes drilled on the 2 inner edges allow for magnets to be inserted. Welded to the inner edge of the Cassette Cover. Please see drawing for details.